(Manufactory) GPS Auto/Vehicle/Navigation Active Tracker Antenna

Specifications

Car antenna
Center Frequency 1575.42 MHz
Band Width 5 MHz
LNA Gain 29 dB
Noise Figure 1.5 dB

 

Gps Antenna For Android

 

Advantages:

 

1.We have our own factory, offering dozens of antenna lines and over 20 R&D personnel.
2.We can make your own bespoke designs and samples to order.

 

 

   3.We have an impressively quick reaction time to all your orders and requests, pre-production.
4. In Jinchang's R&D office, the Technical personnel to meet various requirements for you.

 

 

 

 

3.Electrical Characteristics

3.1 Dielectric Antenna

                                              Form 1

No.	Item	Specifications	Post Environmental Tolerance
1	Center Frequency(MHz)	1575.42 MHz	±3 MHz
2	Band Width(MHz)	±5 MHz	± 1MHz
3	V.S.W.R(in BW )	1.5:1	—
4	Gain(Zenith)	3 dB	±0.5 dB
5	Polarization	RHCP	—
6	Impedance	50 Ω

 

  

 

3.2 LNA/Filter

Form 2

No.	Item	Specifications	Post Environmental Tolerance
1	LNA Gain	28±2 dB	±2.5 dB
2	Noise Figure	1.5 dB	—
3	DC Voltage	2.7~5 V
4	DC Current	8~14

 

 

 

3.3  Mechanical

Form 3

 

No.	Item	Specification
1	Cable	RF1.13 or others
2	Connector	IPEX or others
3	Mounting	Internal

 

4     Reliability

 

Condition:Temperature: 40±5°C

Load: DC=5V±0.5 V

Quantity: 2000pcs

Sustained Time: 480h

 

5     Environmental Specifications

Post Environmental Tolerance (Refer to the form 1~2)

Condition:Temperature range 25±3°C

Relative Humidity range 55~75%RH

Operating Temperature range -40°C~+85°C

Storage Temperature range -40°C~+100°C

5.1 Moisture Proof

The device should satisfy the electrical characteristics specified in form 1~2 after exposed to the temperature 40±2°Cand the relative humidity 90~95% RH for 96 hours and 1~2 hours recovery time under normal condition.

5.2 Vibration Resist

The device should satisfy the electrical characteristics specified in form 1~2 after applied to the vibration of 10 to 55Hz with amplitude of 1.5mm for 2 hours each in X , Y and Z directions.

5.3 Drop Shock

The device should satisfy the electrical characteristics specified in form 1~2 after dropping onto the hard wooden board from the height of 30cm for 3 times each facet of the 3 dimensions of the device.

5.4 High Temperature Endurance

The device should satisfy the electrical characteristics specified in form 1~2 after exposed to temperature 80±5°Cfor 24±2 hours and 1~2 hours recovery time under normal temperature.

5.5 Low Temperature Endurance

The device should also satisfy the electrical characteristics specified in form 1~2 after exposed to the temperature -40°C±5°Cfor 24±2 hours and to 2 hours recovery time under normal temperature.

5.6 Temperature Cycle Test

The device should also satisfy the electrical characteristics specified in form 1~2 after exposed to the low temperature -25°C and high temperature +85°C for 30±2 min each by 5 cycles and 1 to 2 hours recovery time under normal temperature.

....

 If you want to know more information about our products welcome to contact us in any time, And welcome to our company! We display more new products in our showroom.