Home > Products > Wireless Module > TI's chip module CC2500 CC2590 2.4G RF transceiver 2.4ghz rf module
TI's chip module CC2500 CC2590 2.4G RF transceiver 2.4ghz rf module
- 10000 Piece / Pieces per Month
- Shekou Shenzhen
- T/T Credit Card
-
CC2500 small size low cost 2.4Ghz low power 500Kbps wireless module
-
High receiver sensitivity RF module CC2500 programmable wireless module
-
CC1101 433Mhz wireless module transceiver and receiver low power 200M RF module
-
CC2540 2.4G BLE SOC wireless module
-
RS485 interface GFSK modulation transmit distance 1KM wireless module
-
UART port wireless module 800M transmit distance
Product Details
| Place of Origin: | Guangdong, China | Brand Name: | V-chip | Model Number: | VT-CC2500PA-M1 |
Product Description
General Description
VT-CC2500PA-M1 is based on RF transceiver CC2500 of TI Chipcon. CC2500 is a low-cost 2.4 GHz transceiver designed for very low power wireless applications. The circuit is intended for the 2400-2483.5 MHz ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency band. The max RF output power can be set as high as +1dBm, with data rate as high as 500Kbps. The module integrated PA CC2590 to make the max RF output power up to +20dBm. There is an inverted F antenna on the module. So you can use the module conveniently and reducing your development time.
Features
l Central frequency is 2433MHz, Frequency bands: 2400~2483.5MHz
l Programmable output power up to +10dBm, the transmission distance is above 800m in sight .
l High receiver sensitivity down to -109dBm(2.4Kbps)
l Programmable baseband modulator with GFSK/2-FSK/ASK/OOK/MSK
l Programmable data rate 1.2~500Kbps
l Separate 64-byte transmit/receive FIFOs.
l Built-in CRC check ensure data transmission reliably.
l Support carrier sense indicator and digital RSSI output.
l Low current consumption with receive mode <30mA, transmit mode at +20dBm output power <160mA
l Low current consumption at power down state <2uA
l Wake-on-radio functionality for automatic low-power RX polling
l Integrated analog temperature sensor
l Efficient SPI interface, all registers can be programmed with one “burst” transfer
l Small dimension: 30.0mm×21.0mm×2.4 mm
l Operating supply voltage: 2.4~3.6V DC
Applications
l Logistics Tracking System, Warehouse patrol, Electronic label.
l Replace RS232 and RS485 in data transmission
l Industrial monitoring and control in data acquisition
l AMR – Automatic Meter Reading
l Home and building automation
l Consumer Electronics products of wireless control
l Wireless alarm and security systems
l Wireless sensor networks
General Characteristics
Test operating conditions:Ta=25°C,VCC=3.3V if nothing else stated.
Parameter | Type | Condition/Note |
Operating supply voltage | DC 2.4~3.6V |
|
Central frequency | 2433MHz | Can be programmable to other frequency in bands 2400~2483.5MHz |
Frequency accuracy | ±30KHz |
|
Modulation format | GFSK/2-FSK/ASK/OOK/MSK | Programmable |
Transmit power | -30~+20dBm | Programmable |
TX current consumption | <160mA | Po=+10dBm |
Receiver sensitivity | -109dBm | 2.4Kbps |
RX current consumption | <30mA | 2.4Kbps |
Sleep State current consumption | <2uA | Refer to IC operation states |
Data rate | 1.2~500Kbps | Programmable |
Spurious emissions and harmonics | < -30dBm | TX power +10dBm. |
Communication distance | >1000m | 2-FSK modulation, 2.4kbps data rata, +10dBm output power. |
Antenna impedance | 50ohm | Multilayer Chip Antenna |
Operating temperature | -20~+75 °C |
|
Storage temperature range | -50~+125°C |
|
Dimension | 30.0mm×21.0mm×2.4mm | See more in PCB description |
Note:
1. The module transmission data rate will affect transmission distance ,the higher the data rate , the closer the distance, and the lower the receiving sensitivity.
2. The supply voltage to the module will affect TX power, in the operating supply voltage range, the lower the voltage, the lower the TX power.
3. The module central frequency will change as the operating temperature change, use it under suggest temperature, the module can work well.
4. The antenna will strongly affect the communication distance, please select matched antenna and connect it correctly.
5. The module mount will affect the communication distance.
PCB Description
Pin Configuration
Pin name | Pin type | Description |
3.3V | Power(Analog) | 2.4V - 3.6 V analog power supply connection. |
GND | Ground | Connect to the system ground. |
SI | Digital Input | Serial configuration interface, data input. |
SCLK | Digital Input | Serial configuration interface, clock input. |
SO | Digital Output | Serial configuration interface, data output. Optional general output pin when CSN is high. |
GDO2 | Digital I/O | Programmable Clock output, down-divided from XOSC |
GDO0 | Digital I/O | Programmable Clock output, down-divided from XOSC. |
CSN | Digital Input | Serial configuration interface, chip select, active low. |
ANT | RF I/O | RF output signal from PA, connect to the Antenna. |
PA | Digital Input | RX mode:LNA=0(Low);PA=1(High) TX mode:LNA=1(High);PA=0(Low) |
LNA | Digital Input |
Circuit Interface
Note:
1. The module power supply voltage range is DC 1.8~3.6V, above DC 3.6V, the module will damage. It is recommended work at DC 3.3 V.
2. The module interface use half circle pad to soldering on the system PCB board, the GND must soldering to the system digital GND reliably.
3. The antenna must the get to the module’s ANT pin as close as possible.
4. The MCU which don’t have integrated SPI interface can also control the module, use the normal I/O port to work like SPI timing to read and write. The SPI data rate is below 10MHz.
5. The interface can connect directly to the MCU which use 3.3V power supply, there is no need serial resistor. If the I/O is open-drain, the pull-up resistor will be added. When connect to the MCU which use 5V power supply, the MCU’s I/O output current beyond 10 mA, a 2~5k ohm resistor will be series to divide the voltage, or it will damage the module.
6. The module’s pin GDO0 is a general digital I/O port, it can be programmable to produce trigger signal or clock output.
7. The PA control voltage have an effect on the communicate distance and power consumption. In transmit mode, set TE=0 and RE=1; in receive or sleep mode, set TE=1 and RE=0.
8. In the multiple channel application, the channel spacing is recommended to set as 1MHz, or there will be a same frequency interference.
Operation States
CC2500’s operation states contain: Sleep State, Idle State, Active State,Sleep State is the lowest power mode. After wake up from Sleep State, the module get into Idle State. Except the Sleep State, each state can be switch by SPI interface, also programmed to auto-switch. CC2500’s radio control state diagram is shown as below, for detail information in the CC2500 datasheet.
Data Transmission
The CC2500 contains a 64 byte transmit/receive FIFOs, built-in hardware support for packet oriented radio protocols, e.g. Preamble bytes, Synchronization Word, Whitening the data, CRC checksum, Interleave and Forward Error Code, Address checksum. The SPI interface is used for sending commend control and writing to the TX FIFO.
The format of the data packet can be configured and consists of the following figure:
In addition, CC2500 supports fixed packet length protocols, variable packet length protocols and infinite packet length. Details refer to the CC2500 datasheet.
Configuration Registers
The configuration of CC2500 can be done with software SmartRF Studio7. Complete descriptions of the registers are given in the CC2500 datasheet. We can provide evaluation board and demo code to the customer to develop and evaluate the module’s capability.
Dimension
Questions and Answers
Description | Reason and Solution |
Can’t communication | 1.The power supply connect not well, check the module VCC whether it is out of maximum rating. 2.The signal line connect not well, check the module SPI interface. 3.The settings of the transmitter module and receiver module are not the same. Check these modules’ register configuration. 4.Signal block. If the transmitter work with a high TX power, and the receiver was put at a short distance(<0.5m), maybe there is a signal block to make no communication. |
Communication distance is too short | 1.The application environment is too bad or the antenna is shield. Put the antenna to a better place outside or higher throw a coaxial line , replace it with a higher gain antenna. 2.The work space contains a same frequency interference source, or a strong magnetic field interference,power source disturbance. Try to change the carrier frequency or get far away from the source of the disturbance. 3.The power supply is not strong. Check the voltage and the current whether it is enough. |
High data error | 1.The power supply ripple is too big, Change the power supply. 2.Check the module register configuration, it is recommended to set as the CC2500-datasheet. 3.There is a carrier frequency interference, change the channel. 4.The antenna unmatched to the module RF interface, change another matched antenna. |
General Description
VT-CC2500PA-M1 is based on RF transceiver CC2500 of TI Chipcon. CC2500 is a low-cost 2.4 GHz transceiver designed for very low power wireless applications. The circuit is intended for the 2400-2483.5 MHz ISM (Industrial, Scientific and Medical) and SRD (Short Range Device) frequency band. The max RF output power can be set as high as +1dBm, with data rate as high as 500Kbps. The module integrated PA CC2590 to make the max RF output power up to +10dBm. There is an inverted F antenna on the module. So you can use the module conveniently and reducing your development time.
Features
l Central frequency is 2433MHz, Frequency bands: 2400~2483.5MHz
l Programmable output power up to +10dBm, the transmission distance is above 800m in sight .
l High receiver sensitivity down to -109dBm(2.4Kbps)
l Programmable baseband modulator with GFSK/2-FSK/ASK/OOK/MSK
l Programmable data rate 1.2~500Kbps
l Separate 64-byte transmit/receive FIFOs.
l Built-in CRC check ensure data transmission reliably.
l Support carrier sense indicator and digital RSSI output.
l Low current consumption with receive mode <30mA, transmit mode at +20dBm output power <160mA
l Low current consumption at power down state <2uA
l Wake-on-radio functionality for automatic low-power RX polling
l Integrated analog temperature sensor
l Efficient SPI interface, all registers can be programmed with one “burst” transfer
l Small dimension: 30.0mm×21.0mm×2.4 mm
l Operating supply voltage: 2.4~3.6V DC
Applications
l Logistics Tracking System, Warehouse patrol, Electronic label.
l Replace RS232 and RS485 in data transmission
l Industrial monitoring and control in data acquisition
l AMR – Automatic Meter Reading
l Home and building automation
l Consumer Electronics products of wireless control
l Wireless alarm and security systems
l Wireless sensor networks
General Characteristics
Test operating conditions:Ta=25°C,VCC=3.3V if nothing else stated.
Parameter | Type | Condition/Note |
Operating supply voltage | DC 2.4~3.6V |
|
Central frequency | 2433MHz | Can be programmable to other frequency in bands 2400~2483.5MHz |
Frequency accuracy | ±30KHz |
|
Modulation format | GFSK/2-FSK/ASK/OOK/MSK | Programmable |
Transmit power | -30~+20dBm | Programmable |
TX current consumption | <160mA | Po=+10dBm |
Receiver sensitivity | -109dBm | 2.4Kbps |
RX current consumption | <30mA | 2.4Kbps |
Sleep State current consumption | <2uA | Refer to IC operation states |
Data rate | 1.2~500Kbps | Programmable |
Spurious emissions and harmonics | < -30dBm | TX power +10dBm. |
Communication distance | >1000m | 2-FSK modulation, 2.4kbps data rata, +10dBm output power. |
Antenna impedance | 50ohm | Multilayer Chip Antenna |
Operating temperature | -20~+75 °C |
|
Storage temperature range | -50~+125°C |
|
Dimension | 30.0mm×21.0mm×2.4mm | See more in PCB description |
Note:
1. The module transmission data rate will affect transmission distance ,the higher the data rate , the closer the distance, and the lower the receiving sensitivity.
2. The supply voltage to the module will affect TX power, in the operating supply voltage range, the lower the voltage, the lower the TX power.
3. The module central frequency will change as the operating temperature change, use it under suggest temperature, the module can work well.
4. The antenna will strongly affect the communication distance, please select matched antenna and connect it correctly.
5. The module mount will affect the communication distance.
PCB Description
Pin Configuration
Pin name | Pin type | Description |
3.3V | Power(Analog) | 2.4V - 3.6 V analog power supply connection. |
GND | Ground | Connect to the system ground. |
SI | Digital Input | Serial configuration interface, data input. |
SCLK | Digital Input | Serial configuration interface, clock input. |
SO | Digital Output | Serial configuration interface, data output. Optional general output pin when CSN is high. |
GDO2 | Digital I/O | Programmable Clock output, down-divided from XOSC |
GDO0 | Digital I/O | Programmable Clock output, down-divided from XOSC. |
CSN | Digital Input | Serial configuration interface, chip select, active low. |
ANT | RF I/O | RF output signal from PA, connect to the Antenna. |
PA | Digital Input | RX mode:LNA=0(Low);PA=1(High) TX mode:LNA=1(High);PA=0(Low) |
LNA | Digital Input |
Circuit Interface
Note:
1. The module power supply voltage range is DC 1.8~3.6V, above DC 3.6V, the module will damage. It is recommended work at DC 3.3 V.
2. The module interface use half circle pad to soldering on the system PCB board, the GND must soldering to the system digital GND reliably.
3. The antenna must the get to the module’s ANT pin as close as possible.
4. The MCU which don’t have integrated SPI interface can also control the module, use the normal I/O port to work like SPI timing to read and write. The SPI data rate is below 10MHz.
5. The interface can connect directly to the MCU which use 3.3V power supply, there is no need serial resistor. If the I/O is open-drain, the pull-up resistor will be added. When connect to the MCU which use 5V power supply, the MCU’s I/O output current beyond 10 mA, a 2~5k ohm resistor will be series to divide the voltage, or it will damage the module.
6. The module’s pin GDO0 is a general digital I/O port, it can be programmable to produce trigger signal or clock output.
7. The PA control voltage have an effect on the communicate distance and power consumption. In transmit mode, set TE=0 and RE=1; in receive or sleep mode, set TE=1 and RE=0.
8. In the multiple channel application, the channel spacing is recommended to set as 1MHz, or there will be a same frequency interference.
Operation States
CC2500’s operation states contain: Sleep State, Idle State, Active State,Sleep State is the lowest power mode. After wake up from Sleep State, the module get into Idle State. Except the Sleep State, each state can be switch by SPI interface, also programmed to auto-switch. CC2500’s radio control state diagram is shown as below, for detail information in the CC2500 datasheet.
Data Transmission
The CC2500 contains a 64 byte transmit/receive FIFOs, built-in hardware support for packet oriented radio protocols, e.g. Preamble bytes, Synchronization Word, Whitening the data, CRC checksum, Interleave and Forward Error Code, Address checksum. The SPI interface is used for sending commend control and writing to the TX FIFO.
The format of the data packet can be configured and consists of the following figure:
In addition, CC2500 supports fixed packet length protocols, variable packet length protocols and infinite packet length. Details refer to the CC2500 datasheet.
Configuration Registers
The configuration of CC2500 can be done with software SmartRF Studio7. Complete descriptions of the registers are given in the CC2500 datasheet. We can provide evaluation board and demo code to the customer to develop and evaluate the module’s capability.
Dimension
Contact Us
- Shenzhen V-Chip Micreosystems Inc.
- Contact nameVincent Tang Chat Now
- Phone86-755-88844812
- Address floor, 4 building,Nan Shan Yungu Innovation Industrial Park, No.1183,Liuxian Road, Nanshan District, Shenzhen,Guangdong
| New Products | Smart Lighting | Wireless Module |
-
UART port wireless module 800M transmit distance 433M PA RF module
-
USB port 5.0DC power programmed high quality power amplifier RF module
-
1000M long transmit distance 485 interface RF module
-
800M transparent long transmit distance programmed UART interface RF module high sensitivity
-
1200M transparent long transmit distance USB interface RF module high sensitivity
-
low cost CC2500 high receiver sensitivity RF module
-
433.92mhz wireless rf receiver transmit module low cost
-
868mhz wireless rf receiver transmit module low cost wireless transmitter receiver
-
1km long distance transmit cc1120 433Mhz RF module
-
RF Transceiver CC1120 chipcon 1500M long distance automatic meter reading RF module 433m rf module
-
RF Transceiver CC1120 chipcon 1500M long distance 433mhz water meter RF module
-
1km wireless transmitter and receiver module long range rf transceiver module rf 169mHz Wireless module
-
Long transmit distance cc1120 1500M RF module 169mhz Industrial monitoring
-
CC1110 Wireless module UHF transceiver 8051MCU 433mhz rf module
-
200M low power small size 10dBm 433.92mhz receiver rf module
-
Long range transmit distance integrated PCBA rf module CC1110 rf module
-
433.92mhz wireless rf receiver module low cost rf transceiver module rf module
-
Simple cheap wireless receiver wireless module 433M module
-
800 meters transparent communication UART interface data collect rf module
-
Programmed rf module 800M transmit distance wireless sensor network rf module 433M
-
program free rf module communication
-
5000M super far distance transmit distance 433M LNA anti noise circuit rf module
-
POS system transmit rf module 800M home automation part 915M rf module
-
small size build in MCU CC1110 Wireless module UHF transceiver 8051 433M
Popular Searches
- usb bluetooth dongles
- bluetooth adapter
- bluetooth dongle
- stereo receiver
- bluetooth handsfree car kit
- bluetooth car kit
- stereo receiver adapter
- bluetooth car kits
- bluetooth receiver
- bluetooth audio receiver
- bluetooth key finder
- Bluetooth Keyfinder
- 3km wireless wifi network
- car bluetooth kit
- bluetooth car audio kit
- car audio music kit
Recommended Products
- i.MX8M 1.8GHz 64-Bit Embedded ARM Computer with CAN RS485 Supports Ubuntu for Smart Cities
- i.MX8M+ Arm Cortex-A8 / M53 1.8GHz Embedded ARM Computer Compatible with Python for Machine Learning
- i.MX8M ARM Embedded Computer 64-Bit with CAN DI DO Support FreeRTOS for Industrial Automation
- Embedded ARM Rugged Industrial Controller i.MX6ULL with CAN RS485 Supports Debian OS for IIOT
- I.MX6ULL+ ARM Cortex-A7 Embedded System with CAN Support QT Node-Red for Digital Factory
- I.MX6ULL +ARM Cortex-A7 Embedded Computer with CAN/DI/DO Support LINUX OS
- I.MX6ULL + ARM Cortex-A7 Embedded Computer Compatible with Python for Machine Learning
- I.MX6ULL 800MHz Embedded ARM Controller Compatible with LINUX, Ubuntu OS for Rail Transit
- Embedded Computer i.MX6ULL +ARM Cortex-A7 Compatible with Node-Red for Human-Computer Interaction
- T113-i 2*A7 32-Bit ARM Controller ARMxy Series Compatible with Docker for Home Assistant
- OEM ARMxy Series T113-i 2*A7 ARM Controller with CAN/GPIO /Python/Linux OS for Edge Computing
- T113-i 2*A7 ARM Industrial Controller ARMxy Series Compatible with Node-RED for Industrial Automation
Find Similar Products By Category
- Telecommunications > Communication Equipment > Wireless Networking Equipment
- Please Enter your Email Address
- Please enter the content for your inquiry.
We will find the most reliable suppliers for you according to your description.
Send Now-
Vincent Tang
Welcome to my shop! Glad to serve you!Please send your question!
Your message has exceeded the limit.
- Contact supplier for lowest price
- Customized Request
- Request Sample
- Request Free Catalogs
Your message has exceeded the limit.
-
Purchase Quantity
-
*Sourcing Details
Your inquiry content must be between 20 to 5000 characters.Send Now.
-
*Email
Please input the mailbox.
-
Mobile