PTZ control 12v Output 3.5" HVGA TFT-LCD screen 1080P HD coaxial AHD Camera tester

3.5" HVGA TFT-LCD screen 1080P HD coaxial AHD Camera test PTZ control 12v Output

The new HD coaxial tester is developed for the On-Site installation and maintenance of coaxial camera,it also combine other functions analog camera test, video level meter, analog signal output, IP address scan, Ping, port finder, UTP test, digital multimeter ,optical power meter and TDR cable tester etc. Its portability, user-friendly design and many other functions make the IP tester an essential tool for all installers or technicians.

Apply for:

— CCTV system installation and maintenance

— Network cabling project installation and maintenance

— Dome camera and all in one camera testing

— Video transmission channel testing

— PTZ control

Features with:

 1)3.5inch screen display, 480(RGB)x320 resolution

2) Low power consumption, working time lasts 7-11 hours

3)LCD screen brightness/contrast/color saturation adjustable NTSC/PAL auto adjust

4) AHD coaxial camera image display, coaxial PTZ control and call up the camera OSD menu

5)Enhanced Color bar generator, PAL/NTSC multi-system color bar video generator (Eight-system switchable, transmit/receive eight- system colorful images).

6) LED Flashlight.

7) HD coaxial control, PTZ control, color bar generator shortcut key.

8) F1, F2 user-defined key

9) Visual fault locator, to test fiber’s bending and breakage * (Optional)

10) Digital Multi-meter, DC and AC voltage measurement, Resistance measurement Continuity test, Diode measurements, Capacitance measurement *(Optional)

11) Cable tracer, by sending the audio signal, enables the blue cable tracer tester to find the connected cable from messy cables. * (Optional)

12) Ping test, PING is the most conventional network debugging tools; it is used for testing if the connected IP camera or other network equipment's Ethernet port is working normally and the IP address is correct.

13) IP address scan The IP address scan can quickly search for connected IP cameras or another network device IP address

14) POE Voltage tests the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an Ethernet cable.

15) Port Finder,it will enable the installer to easily and quickly find the connected port for an Ethernet cable.

16) Link monitor check if the new setting IP address is occupied.

17) TDR cable test, TDR break-point and short-circuit measurement. * (Optional)

18) PTZ control and PTZ protocol analysis
19) Cable test, Test LAN cable or telephone cable, UTP cable etc, cable type and the sequence of wires will be displayed

20) Support more than 30 protocols, such as Pelco-D, Pelco-P, SAMSUNG.

21) Support RS232/RS485,rate 600 ~ 115200bps adjustable

22) Built in Lithium Ion Polymer Battery(3.7V DC 3000mAh )

23) Image display and data control integration

24) Handheld HD coaxial tester, easy to carry and operation.

25) Optical power meter, test fiber loss and value * (Optional)

1. Video signal test

The new HD coaxial tester ,built-in high definition 3.5”LCD-TFT 480(RGB)x320 resolution, view the image, easy and directly displays the camera image , support PAL/NTSCLCD screen brightness/Contrast/Color Saturation adjustable. Suitable for field construction and maintenance work

2. HD coaxial signal test

AHD coaxial signal test, support 720p 25/30fps/ 1080p 25/30fps, the tester will display camera image, coaxial PTZ control and call up the camera OSD menu.

3. Video signal level test (Not for TVI CVI AHD test)

Test video signal strength attenuation, longer video signal cable will cause the image to be dim, and reduce the image dynamic range, video signal is too strong, it will cause the virtual shadow, and reduce the sharpness of the image. It also can real-display the video level value, if out of range, notices will be display in the screen.

4. PTZ controller

Display the input video images. Pan/tilt the P/T unit and zoom in/ out the image. Setup the controlling parameters like protocol, communication port, baud rate, PTZ ID, pan/tilt speed; set and call preset position.

5. Enhanced color bar generator

The tester sends out color bars via its BNC output to the monitor. This is used to test for a problem in the cable going from the camera back to the monitoring area

6. DC12V 1A output power

Power the camera with DC12V (1A) power output from the tester. It is helpful for demo and testing when the power supply is not available.

7. Audio testing

Test the audio input from pickup devices. Connect the tester and pickup device with the audio cable.

8. Cable tester

Test LAN cable or telephone cable.

Connect LAN cable or telephone cable with the HD coaxial tester and cable tester. And then the connecting status, cable type and the sequence of wires will be displayed, as well as the serial number of the cable tester kit.

9. PTZ controller

Search the Control protocol code from Multifunction keyboard or DVR by RS485 /RS232 interface, test the PTZ control command data whether received anomaly and RS485/RS232 data transmission.

Screen displays 16 hexadecimal codes such as

PELCO-P: A0 00(Add) xx xxxxxx AF xx

PELCO-D: FF 01(Add)xx xxxxxxxx

10. PTZ address scanning

Search up the ID of PTZ camera. Help the engineer search the speed dome address quickly.

11. Cable scan (Optional) *

Send the specific signal, easy to find the connected cable from the mess cable

12. Port finder

The tester will send signals to make the connected PoE port flicker at a set frequency. This will enable the installer to easily and quickly find the connected port for an Ethernet cable.

13. IP address san

The IP address scan can quickly search for connected IP cameras or another network device IP address.

14. Link monitor

To add an IP camera or other network device to the current network group, the new IP address must not be occupied; otherwise it will cause IP conflicts and stop the equipment normal working. Link monitor can check if the new setting IP address is occupied.

15. PING test

PING is the most conventional network debugging tool; it is used for testing if the connected IP camera or other network equipment is working normally and the IP address is correct.

16. PoE test

Test the PoE voltage from a PoE switch. The unit will clearly display the voltage for each wire in an Ethernet cable.

17. Visual fault locator * (Optional)

Visual Fault Locator with 650nm wavelength can emit red laser sources to test multi-mode and single mode fiber’s bending and breakage, and Continuous light-emitting and 1HZ, 2Hz modulating light output. It is indispensable tool in fiber project constructing, fiber net-work maintaining, optical component manufacture and research.

18. Digital multimeter (Optional)*

HD coaxial tester built in highly stable and reliable 33/4 digit (6600) digital multimeter. It is used for the DC and AC voltage measurement,AC and DC current measurement, Resistance measurement, Continuity test, Diode measurements, Capacitance measurement, Auto/Manual measuring range switching, relative value measurement and locking . It is easy operation and professionally accurate.

19. LED lamp

Press the LED On/Off button to use the LED flashlight.

20. HD coaxial, PTZ control and color bar generator shortcut key

HD coaxial, PTZ control and color bar generator shortcut key, easy to operate

21. F1, F2 User-defined shortcut keys

The user-defined shortcut key is designed for improving the efficiency for the engineer, anytime press, easy to operate.

22. TDR cable test * (Optional)

TDR cable testing, accurately measure BNC cable, network cable, controls cable's open circuit and short-circuits location. It greatly improves working efficiency

23. Optical power meter, test fiber loss and value * (Optional)

The IP camera tester adopts the most advanced handheld instrument specific integrated chip , achieve ultra-low power operation, with the 7 TFT-LCD High-definition screen display ,five wavelength calibration points 1625nm,1550nm ,1490nm , 1310nm , 1300nm , 850nm.Linear or nonlinear optical power display, it can measure the optical power value, and also be used for Relative measurement of optical fiber link loss.

Note: With sign“*”means functions are optional, Optional function need pay additional cost if asked to add any one of them in the tester 

Model HD coaxial tester HD-2800 series [*]models are Optional
Video Test
Signal mode NTSC/PAL (Auto adapt)
Display 3.5 inch digital TFT-LCD ,480(RGB)x 320 resolution
LCD adjustment Brightness, Contrast, Saturation adjustable
Video IN/OUT 1 channel BNC Input & 1 channel Output
Video Output Mode 1.0 Vp-p
Video Level test
Level test Video signals measured in IRE or mV (not for TVI,CVI ,AHD)
Video level meter (Optional)
Video Level meter PEAK video signal level, SYNC signal level, COLOR BURST chroma level measurement
PTZ controller
Communication Support RS232 and RS485
PTZ Protocol Compatible with more than 30 protocols such as PELCO-D/P, Samsung, Panasonic, Lilin, Yaan, etc.
Baud Rate 600,1200,2400,4800,9600,19200,57600,115200bps
Video signal generation
Color bar generator Output one channel PAL/NTSC color bar video signal for testing monitor or video cable.(red, green ,blue, white and black color )
UTP cable tester
UTP cable test Test UTP cable connection status and display in the screen. Read the number of the test box.
DC12V 1A power output
DC12V power output Output DC12V1A power for camera
Audio input test
Audio input test test the pickup and other audio equipments on the front-end
RS485 data analysis
Data Monitor Captures and analyzes the command data from controlling device
CVI test(Optional)*
CVI video signal test 1 channel CVI in(BNC interface)support 720p 25/30/50/60fps,1080p 25/30fps,camera OSD menu control over coaxial cable
TVI test(Optional)*
TVI video signal test 1 channel TVI in(BNC interface) support 720p 25/30/50/60fps,1080p 25/30fps,camera OSD menu control over coaxial cable
AHD test(support)
AHD video signal test 1 channel AHD in (BNC interface)support AHD 2.0 version, 720p 25/30fps,1080p 25/30fps,camera OSD menu control over coaxial cable
Port flicker
Port flicker Find the connected POE port quickly.
IP scan, Link monitor, PING test
IP scan Find out the connected IP camera or the other network equipment IP address quickly.
Link monitor Check the IP address whether is occupied
PING testing Test IP camera or Ethernet port of the other network equipment whether work normally, and check the IP address
Cable scan (Optional) *
Cable scan Search the cable by the audio signal
PoE tester
PoE tester Display the power supply voltage and cable connection states
Digital Multimeter (Optional) *
AC/DC Voltage 0-660V auto/manual range, the min resolution is 0.1mV
AC/DC current 660.0uA , 6.600mA, 66.00mA , 660.0mA, 10.00A
Resistance 660.0Ω, 6.600kΩ, 66.00kΩ, 660.0kΩ, 6.600MΩ, 66.00MΩ
Capacitance 6.6nf~66000uF, the min resolution is 1pf
Diode 0~2V forward voltage, the min resolution is 1mV
Data hold Hold and display the measured value
Relative measurement Display the relative power value
Continuity testing Built-in buzzer will sound, if resistance is lower than 50 Ω
Testing speed 3 times/ seconds
Data range -6600~+6600
Optical power meter (Optional) *
Calibrated Wavelength(nm) 850/1300/1310/1490/1550/1625nm
Power range(dBm) -70~+10dBm
Sensitivity(nW) 0.001nW
Connector type FC/PC
Data hold Hold and display the measured value
Relative measurement Display the relative power value
Visual fault locator (Optional) *
Visual fault locator Test fiber’s bending and breakage ( SM and MM fiber)
TDR Tester (Optional) *
TDR Tester breakpoint and short circuit measurement(BNC cable, telephone cable)
POWER
Power Adapter DC 5V(1.5A)
Battery Built-in 3.7V Lithium polymer battery ,3000mAh
Rechargeable After charging 3-4 hour, working time lasts 11 hours
Low Consumption Energy saving technology, the battery icon real-time display
Parameter
Operation setting English/Chinese and other languages OSD menu
Auto off 5-60 (mins)
Keytone On/Off
General
Working Temperature -10℃ ~+50℃
Working Humidity 30%~ 90%
Dimension/Weight 194mm x 112mm x 48mm / 540g