Home > Products > Brushless DC Motor > Custom IEC 200w high eddiciency ACBrushless permanent magnet dc synchronous motors synchronous for sale

Share|

Custom IEC 200w high eddiciency ACBrushless permanent magnet dc synchronous motors synchronous for sale

FOB Price

USD $220 - $300 / Unit

1 Unit(Min.Order)

Supply Ability 10000 Unit / Units per Month
Port FOB Ningbo
Payment Terms:T/T Credit Card

Request Sample Customized Request Download Product Catalog

Contact Now

Get lowest price

Product Details

Brand Name:	Volcano Electric	Place of Origin:	Zhejiang, China	Model Number:	VOL-IEC63S200-4P-05
Type:	Asynchronous Motor	Frequency:	60HZ
AC Voltage:	208-230 / 240 V	Certification:	CCC, CE, ROHS	Phase:	Three-phase
Protect Feature:	Drip-proof

Product Description

Product Display

Motor type	Output Power	Voltage	Load	Speed	Rated Torque	Efficiency	Noise	IP Class
Motor type	KW	V	A	RPM	Nm	%	dB	IP Class
VOL-BL2K5A48	2.5	48	56.00	1500	15.92	92	62	IP 54
VOL-BL2K5A72	2.5	72	37.34	1500	15.92	92	62	IP 54
VOL-BL2K5A110	2.5	110 ac	14.11	1500	15.92	92	62	IP 54
VOL-BL2K5A220	2.5	220 ac	7.05	1500	15.92	92	62	IP 54
VOL-BL2K5A380	2.5	380 ac	4.08	1500	15.92	92	62	IP 54

VIEW MORE PLS CONTACT US >>>

Other Products

Process Flow

About Us

Packing&Transport

Q:Motor has been running then fails to start,what to do?
A:Likely cause: Fuse or circuit breaker is tripped.

What to do: Replace the fuse or reset the breaker.

Likely cause: Armature is shorted. Motor may make a humming noise and the circuit breaker or fuse will trip.
What to do: Disassemble motor and inspect the armature for a burnt coil. Inspect the commutator for burnt bars. If this condition exists, the motor needs to be replaced.

Likely cause: The brushes may be worn down too far and no longer make contact with the commutator.
What to do: Check the brushes to make sure that they are still making contact with the commutator. Contact manufacturer for brushes.

Likely cause: Controller may be defective.
What to do: Verify voltage is coming out of the controller.

Q: On initial installation, motor fails to start up,what to do?
A: Likely cause: Motor is incorrectly wired
What to do: Verify that the motor is wired correctly.

Likely cause: No output power from controller.
What to do: Measure voltage coming from the controller.

Likely cause: Motor is damaged and the armature is rubbing against the magnets.
What to do: Disassemble motor and see if the armature can be realigned by reassembly. Motor may have to be replaced.

Q: Motor takes too long to accelerate,what to do?
A: Likely cause: Motor controller not properly set.
What to do: Adjust the acceleration trim pot of the controller.

Likely cause: Brushes are worn.
What to do: Verify brush length.

Likely cause: Bearings may be defective.
What to do: Inspect bearings. Noisy or rough bearings should be replaced.

Q: Motor runs in the wrong direction,what to do?
A: Likely cause: Incorrect wiring
What to do: Interchange the two motor leads.

Q: Motor runs OK but has a clicking noise,what to do?
A: Likely cause: Suspect a burr on the commutator.
What to do: Remove burr from commutator using a commutator stone.

Contact Us

Ningbo Haofeng Magnet Technology Co., Ltd.

*Email
Please enter Your valid email address.
*To

Ningbo Haofeng Magnet Technology Co., Ltd.
*Message
Your inquiry content must be between 20 to 5000 characters.
Please enter a correct verification code.

Product Categories

Alnico magnet	Brush DC Motor	Brushless DC Motor	Drivers
Ferrite magnet	High Voltage BLDC Motor	Low Voltage BLDC Motor	Neodymium magnet
Others	Pot magnet	SmCo magnet	Ungrouped

New Products

Custom IEC 200w high eddiciency ACBrushless permanent magnet dc synchronous motors synchronous for sale

Product Details

Product Description

Contact Us

Popular Searches

Recommended Products

Find Similar Products By Category