433 MHz Peach Color Single Button Wireless Button RF Receiver Module Kit Remote Control with Receiver

Main parameters of the remote control:
Working voltage: DC12V/23A
Operating frequency: 315MHz, 433MHz (other frequencies can be customized)
Standby current: 0mA
Working current: 16mA
Coding method: fixed code (2264/2260 chip pad pair code)
                     Learning code (1527 chip)
Modulation method: OOK (amplitude modulation)
Reference distance: generally can reach 30 meters to 80 meters in use, many factors are subject to the test
Working temperature: -10°C~+70°C
Size: 58 x 38 x 14mm

Receiver main parameters:
1. Working voltage: DC2.5V-5V
2. Working current: 3.7mA
3. Sensitivity: -108DBM
4. Rate: MAX 10 KB/S
5. Working mode: jog, self-locking, interlocking (freely convertible)
6. Module output: 4 CMOS level signals, which can correspond to 4 buttons of remote control "ABCD"
7. Receiver module can store remote control: 16
8. Support coding chip model: EV1527, PT2262, 2264, 2260 other customization

When the remote control button is pressed, the four data pins of A B C D corresponding to the modules D0, D1, D2, and D3 output high level, and when not pressed, it is low level.
Clear and match the code: (Before switching the mode, clear the code first)
1, clear function - press the learning button (not let go) "KEY" 5 seconds, after the LED indicator goes out, let go, wait until the LED indicator flashes 3 times and then go out, start to clear all the remote control code data in the memory, it means The clear function is complete.
2, the code function - press the learning button (jog mode) "KEY", the LED indicator lights up to indicate that the microprocessor enters the learning pair code state, press the matching wireless remote control button, the LED indicator flashes 3 After the second time, the code is successful. (The learning button is clicked once for the jog mode; press 2 times for the self-locking mode; press 3 times for the interlock mode; press 4 times: 1, 2 for jog, 3, 4 for self-locking; for 5 times: 1 2, jog, 3, 4 interlock; press 6 times: 1, 2 self-locking, 3, 4 interlock; press 7; 1, 2 interlock, 3, 4 interlock.) The wireless remote control switch can store 16 different remote controls and can set different working modes. (This is a one-key pair code, the program will automatically assign the data bits)
3. Pair code test - After the code is successful, when the remote control button is pressed, the corresponding D0, D1, D2, D3 output is high level.
Wiring and testing
1. Correctly regulate the wiring according to the control function required by yourself. After the wiring is completed, check whether the wiring is correct. Do not operate the wiring and trial wiring with power. If there is any irregular operation, the company will not be responsible.
2. After confirming that the wiring is correct, turn on the power.
3. Press the remote control button of the code, and the remote control switch controls the corresponding control object. If the control is normally controlled, it means that the wiring test is successful and can be used normally.
common problem
1. Turn on the power supply, and clear code and code can be performed at any time. When the circuit is working, the clearing function is performed. After the clearing is successful, the 4-way relay returns to the normal state. When the LED function is lighted, the code enters the code status. The learning waiting time is about 6 seconds. It is necessary to complete the code within 6 seconds. After 6 seconds, the LED indicator is off and the program automatically exits the code status.
2. When using for the first time, be sure to clear the code once and empty the factory test to store the remote control code. After the code is successful, the valid remote control code LED will be lit.
3. The control switch can store 16 remote control codes. If 17 remote control codes are learned, the program will automatically overflow the first remote control code. And so on. When the remote control code is confusing, it should be cleared before learning, so as to avoid interference from other remote control codes.
4. The remote control used needs to learn after coding, because the general coded remote control has no code when it leaves the factory. It is ok to use it directly, but it will be controlled by other remote controllers without coding.
5, use the installation to avoid interference sources and form a similar shield cover environment. Directly affects the receiving sensitivity.
6, do not use it abnormally. Abnormal use will reduce the performance and longevity of the product. If it is serious, it will directly damage the product and bring hidden danger to your safety.

We have strong cooperation with DHL,TNT,UPS,FEDEX,EMS,China Air Post.

You also can choose your own shipping forwarder

1. Your inquiry can be replied in 12 hours.

2. All your questions can be answered by our well-trained and experienced staff in English.

3. Any your customized products we can help you to design and put into production.

4. Protection of your sales area, ideas of design and all your private information.

5. Delivery by DHL, UPS, EMS or by sea as your requirements.

1. Could I order one piece for sample to test the quality?

A: Yes, You could order the sample before your order. We recommend to check the sample before order, to make sure you will get the indeed product that you need.

2. What time can you deliver my order?

Samples in 5-7 working days, bulk order in 7-15 working days after payment.

3. What's your best price?

We make different models and different chip, please advise detailed parameters for goods that you need.

4. Do you have gurantee for my order?

Remote control and receiver gurantee for 1 year